PREVENT COSTLY SAFETY ISSUES
Safely deactivate pyrophoric iron scale from your raw inlet gas filters
Gas filters used to process natural gas can gather iron sulfide deposits, which cause the filter to lower its performance and generates significant heat. FQE® Pyrophoric is a non-toxic, non-hazardous product that is safer to apply than other methods available (i.e., potassium permanganate or acidification).
Deactivated and safe for disposal in 3 steps:
Submerge filter in FQE Pyrophoric for 30 minutes
Let filters dry for at least
Dispose of in waste containers without risk of fire
Trusted by Natural Gas producers across North America
Raw inlet gas filters remove entrained solids present in the incoming feedstock natural gas and typically require change-outs every month. These filters are typically contaminated with pyrophoric iron sulfide and have smoldering issues resulting from the iron sulfide reaction with oxygen in the air.
Water is often used to soak the filters for disposal, resulting in increased disposal costs due to waste volume. Filters that have dried up often pose a potential fire risk. FQE Pyrophoric is a safe and environmentally friendly product that inhibits the oxidation reaction process from taking place.
Simple, safe, and effective deactivation
To deactivate the iron sulfide deposits, the filters are submerged in the FQE Pyrophoric for 30-minutes. The application is done at ambient temperature conditions, and the filters are then left to dry before disposal. Upon completion of the job scope, the filters can be disposed of in traditional waste disposal containers without a fire risk.
You will typically save at least 30% in long-term costs compared to using an oxidizer like potassium permanganate. Our product is selective only to FeS, and typical oxidizers are non-selective.
Get started with a pyrophoric iron management program
The pyrophoric iron management program allows you to fully mitigate the risk of pyrophoric fires while using personnel safe and environmentally friendly product. Contact us to buy today.
Frequently asked questions
How does FQE Pyrophoric work?
FQE Pyrophoric does not work by means of oxidation and functions as an antioxidant. Our chemical bonds with the FeS and works as an antioxidant to prevent any oxidation reactions from occurring.
The product is designed to be specific to FeS and does not react with other materials (compared to competitor oxidation driven products). It is also designed to be environmentally and personnel safe as a biodegradable, non-hazardous product.
How long does FQE Pyrophoric take to work?
The reaction is instantaneous in nature.
What temperatures does FQE Pyrophoric need to be applied at?
The product can be applied at a variety of different temperatures.
Is the effluent generated by FQE Pyrophoric hazardous?
The product is non-hazardous and does not react to create any hazardous byproducts. The classification of waste will be dependent on any hazardous materials being constituents of the original effluent, and anything else added to the final waste stream.
It was designed to be environmentally and personnel safe as a biodegradable, non-hazardous product.
How is FQE Pyrophoric applied?
Diluted Application: It is recommend to dilute the product between 10-20% in water. This leaves enough active ingredient to penetrate the filter deposits and treat the internals of the vessel. You would need to dispose of the resulting effluent as you cannot confirm active ingredient concentration in the fluid without specialized equipment.
Neat Application: Add the product at a 100% neat concentration and preserve the unreacted product that comes out for future use. As long as 100 neat material is available, it is still active material.
How do you determine that the product is still active when diluted, and how do you test for the effectiveness of FQE Pyrophoric chemistry during the application?
If required, a proprietary test can be used by your field staff to confirm the presence of active ingredients. A test to confirm active ingredient content elimination or presence is used to confirm the efficiency of the FQE Pyrophoric product.
As long as you detect the active, you have enough FQE Pyrophoric in the process. If you show no active FQE Pyrophoric, the material had been consumed and you need additional product added to your cleaning solution.
Since the FQE Pyrophoric product is a concentrate, can the residual product be reused?
That is correct, the product is a concentrate, and when used in filter dip applications, the same batch can be used for multiple dip applications in the same batch.
As long as you have product available, there is active ingredient present and therefore the material will continue to function.
Please note if the product is diluted with water, it would need to be tested to confirm that active material is still present.
Is there any color change associated with the reaction?
There is no color change associated with our product as it is not a potassium permanganate based material.
How do you dispose of the FQE Pyrophoric product?
FQE Pyrophoric was designed to be non-hazardous and it as well as any byproducts can be processed through wastewater treatment.
How should FQE Pyrophoric be stored and what is the shelf life of the product?
Product should be stored away in an enclosed area. Recommended Shelf Life is 1 year.
In cold weather locations, we have a freeze protected version of the product at -15F called FQE Pyrophoric-W. The FQE Pyrophoric product is good for 15F.
What packaging sizes can FQE Pyrophoric be purchased in?
FQE Pyrophoric is sold in 55 gallons poly drums, 330 Gallon Totes, and bulk quantities in most geographical Locations.
Minimum order quantities/volumes may apply regions outside of North America.